| Author |
Message |
darkzorn
Posts: 1
Phone Model:
samsung sgh-x426
Service Provider:
Rogers |
 
Thu Dec 08, 2005 10:11 am |
The *#9998*3323# Method:
1. If you have changed your phone password, change your password back to the default 8 zeros (00000000).
2. Put a SIM card that is from a network other than the one your phone is locked to
3. When Incorrect SIM error comes up, type *#9998*3323#.
4. White screen will appear with an exit option. Press the right softkey.
5. From the menu that appears, select the Malloc Fail option. This will reboot the phone and the normal service screens will appear.
6. Type *0141# and then press the green call key. "Personalization" or "Personalized" will appear.
7. Turn off your phone and put the original SIM back in.
8. Turn on your phone. You will receive a prompt to enter a password.
9. Type 8 zeros (00000000)
10. Completed. You have now unlocked your phone.
===================
so i have done it all, i have unlocked the god damn cell phone!!!
but the thing is i still don't have a signal from my new carrier...!!!
what to do?
i'm using globe!!!!!
|
 |
Advertisement
|
|
|
|
|
stewie_thugs
Posts: 1
Phone Model:
i860
Service Provider:
sprint |
Sun Dec 18, 2005 3:11 pm |
|
Can someone send me the software to unclock the x426 Rev 1.6 to my email or post the link on this topic. Im selling a bunch of them.
|
|
MrsIrishOD
Posts: 1
Phone Model:
Samsung SGH X426
Service Provider:
Cingular |
Thu Dec 22, 2005 10:01 am |
Thank you all for this information! My husband has a Samsung SGH X426 phone. When AT&T went to Cingular, he had to buy another phone. He recently dropped his new phone in a parking lot and it got run over. Without insurance on the phone, he would have to dish out another $100++ for yet another phone! By unlocking his original AT&T Samsung, we were able to swap the sim chips and save some bucks!!!
Thank you, thank you, thank you!
|
|
malcontent
Posts: 1 |
Tue Jan 03, 2006 2:12 am |
thanks for the info on the samsung 
|
|
labatia
Posts: 1
Phone Model:
lots
Service Provider:
rogers |
Wed Jan 04, 2006 5:44 pm |
i have the 1.7 but no data cable..i wish there was a way to unlock it without the cable
|
|
cemen777
Posts: 1
Phone Model:
samsung X475
Service Provider:
T_Mobile |
Mon Jan 09, 2006 2:13 pm |
I did entered *#9998*3323# as you discribed in step 4. I received error 3323 wrong code. Also, when I entered 3323 these numbers uppired on screen as _ _ _ _ . I have Samsung X-475 T-Mobile
Please help!
++++++++++++++++++++++++++++
| roswell108 wrote: | Not that I wouldn't love money, but I work free...
Unlocking:
If you have Rev 1.5 (x426) or earlier and most older models
Use the *#9998*3323# Trick (look for it on the forum)
The *#1111*WHATEVER# code will NOT work
If you have Rev 1.6 (x426) or later and most newer models
You MUST use unlocking software. Codes WILL lock your phone FOREVER
Locked: Return for Servicing
There is only 1 working solution, you must flash a copy of the firmware that is not in the locked status. (Most) Unlocking programs will NOT disable this issue, and your service provider cannot give you a code
If you do not plan to use your phone with another service provider, there is no real point to unlocking your phone other than to sell it. If you don't need to unlock it, don't take the risk of disabling the phone altogether
The *#9998*3323# Method:
1. If you have changed your phone password, change your password back to the default 8 zeros (00000000).
2. Put a SIM card that is from a network other than the one your phone is locked to
3. When Incorrect SIM error comes up, type *#9998*3323#.
4. White screen will appear with an exit option. Press the right softkey.
5. From the menu that appears, select the Malloc Fail option. This will reboot the phone and the normal service screens will appear.
6. Type *0141# and then press the green call key. "Personalization" or "Personalized" will appear.
7. Turn off your phone and put the original SIM back in.
8. Turn on your phone. You will receive a prompt to enter a password.
9. Type 8 zeros (00000000)
10. Completed. You have now unlocked your phone.
Cerebros Instructions:
1. Make sure phone is plugged into cable, cable is plugged into computer, drivers are installed, and phone is on.
2. Start Cerebros Unlocker 1.5
3. Click the "Models" drop-down box
4. Select your model from list (q100 = x426/x427)
5. Press Unlock
6. Wait until finished and unplug phone
7. Remove battery, replace, and turn phone on
8. Phone is now unlocked
WinIMEI Instructions:
1. Make sure phone is plugged into cable, cable is plugged into computer, drivers are installed, and phone is on.
2. Start WinIMEI
3. Make sure U.S.A. (Voicestream), A Line, 1 PC, and the com port you are using are selected from the appropriate drop-down menus.
4. All selection boxes should be unchecked
5. Click Write IMEI in the bottom center
6. From the new screen that appears click RD IMEI Setting
7. Wait for TestModeOn Pass and the box in the upper right to display Pass and turn green before proceeding
8. Click UnLock from the button cluster in the bottom right
9. Click both Exit buttons and disconnect phone
10. Your phone is now unlocked
Note: All previously listed programs and an unlocked version of the x426 rev 1.6 firmware and optiflash (for flashing it) are available at my site: http://www.personal.psu.edu/users/s/j/sjs342/ |
|
|
Vladder
Posts: 1 |
Thu Mar 30, 2006 11:13 pm |
I've had the same trouble with the *#9998*3323# as Kalt. I've got as far as entering *0141# and getting the 'Personilised' message. However when I put the original sim card back in, after entering the sim pin, I get a box called 'Sim lock' and entering 00000000 only gives me the 'Wrong card' screen. I works fine with the new sim but I need to use *#9998*3323# every time I insert any other sim. Any ideas??
| kalt wrote: | My english is not well but Iam gonna try to explain you my troubles
I followes all this instruction:
*********************************
The *#9998*3323# Method:
1. If you have changed your phone password, change your password back to the default 8 zeros (00000000).
2. Put a SIM card that is from a network other than the one your phone is locked to
3. When Incorrect SIM error comes up, type *#9998*3323#.
4. White screen will appear with an exit option. Press the right softkey.
5. From the menu that appears, select the Malloc Fail option. This will reboot the phone and the normal service screens will appear.
6. Type *0141# and then press the green call key. "Personalization" or "Personalized" will appear.
7. Turn off your phone and put the original SIM back in.
8. Turn on your phone. You will receive a prompt to enter a password.
9. Type 8 zeros (00000000)
10. Completed. You have now unlocked your phone.
*************************
The real trouble is that when I put the SIM card(wich one of the other network"swisscom").
I turn the phone On.
I type the password of the SIMcard(swisscom)
until here everything is OK
then its display: Verrouillage SIM --->in english "Lock SiM"
and the Phone ask for a password.
---when I put the SIM password(swisscom) it doesn't Work
--when I type "00000000" it also wrong
My question is what I have to do???
Thanks |
|
|
LGX88
Posts: 6
Phone Model:
Nokia 6305i
Service Provider:
Verizon |
Wed Apr 19, 2006 9:29 pm |
Well, it seems no body has been posting here for awile. Buuuut... I need help with my Samsung SGH-X426. OK so its a Rev 1.6 X46UEDC1
AT&T wireless. Im buying a cable to hook it to the computer to unlock it.
The only Problem is... is that i cant find an X426 unlocking software.
I found some websites that let you download it. But eather the program's missing a file, or its crupted or it dosen't support X426 modle oooor the site just went beserk and i cant download it. By any chance can some one help me out here?
Much appreciated! 
PS: Sorry if im just not looking hard enough and its on another post
|
|
sowha
Posts: 1 |
Fri Apr 28, 2006 12:11 am |
I just wanted to thank Roswell 108 for the unlocking information. It worked easily and saved me $.
Thanks again.
|
|
rnprasad
Posts: 1 |
Mon May 01, 2006 6:36 pm |
|
I looked at the website, but it looks like there are links to downloads but the files are not there. I wonder if any of you still have a copy of the cerebros or winIMEI. If someone can send me the file, I would appreciate it and will try to find some webspace to host it too.
|
| | |
|
|
|
|
