| Author |
Message |
shmuil195
Posts: 3 |
 
Sun Mar 13, 2005 12:52 am |
Hi,
I would like to flash my E715 but not until I back it up. I have some data/charging cable that I bought on ebay. It works fine with EasyGPRS, I can send and receive everything. I've tried both versions of OptiFlash that are available in the tutorial. Both OptiFlash versions time out when trying to read memory addresses 0x00006000 - 0x00006fff:
I E159 9:04:03 PM ThreadGUI started
I E160 9:04:03 PM ThreadProtocol started
I E161 9:04:03 PM Boot loader protocol type: passive
I E162 9:04:03 PM Flash loader: C:\Programs\Opti3.6\Models\SGH-E715.sre
I E163 9:04:03 PM Opened COM4 at 115200 baud
I E164 9:04:04 PM PC transfer speeds (COM4): 57600 115200 230400 460800 921600
I E165 9:04:04 PM Loading S-record file: <C:\Programs\Opti3.6\Models\SGH-E715.sre>, RangeCheck=Off
I E166 9:04:04 PM There is 1 memory region in the S-record file:
I E167 9:04:04 PM 1: 0x00000000 - 0x00004a5b = 19036 Bytes
I E168 9:04:04 PM SendFile=C:\Programs\Opti3.6\Models\SGH-E715.sre, Mode=3
I E169 9:04:04 PM Hit On/Off Botton
I E170 9:04:04 PM TalkToBootloader (using COM4)
I E171 9:04:04 PM Talking to passive bootloader
I E172 9:04:30 PM Bootloader V2.2 using UART0
I E173 9:04:30 PM ROM mask ID: 0x00004545 ( EE)
I E174 9:04:30 PM ID register: 0x000203bc (Trident II)
I E175 9:04:30 PM Bootloader type: 3
I E176 9:04:30 PM Max. transfer size: 2176 bytes
I E177 9:04:30 PM Send: 0x00000000 - 0x000007ff (=2048)
I E178 9:04:30 PM Send: 0x00000800 - 0x00000fff (=2048)
I E179 9:04:30 PM Send: 0x00001000 - 0x000017ff (=2048)
I E180 9:04:30 PM Send: 0x00001800 - 0x00001fff (=2048)
I E181 9:04:30 PM Send: 0x00002000 - 0x000027ff (=2048)
I E182 9:04:31 PM Send: 0x00002800 - 0x00002fff (=2048)
I E183 9:04:31 PM Send: 0x00003000 - 0x000037ff (=2048)
I E184 9:04:31 PM Send: 0x00003800 - 0x00003fff (=2048)
I E185 9:04:31 PM Send: 0x00004000 - 0x000047ff (=2048)
I E186 9:04:31 PM Send: 0x00004800 - 0x00004a5b (=604)
I E187 9:04:31 PM TalkToBootloader: OK
I E188 9:04:31 PM Duration: 1s
I E189 9:04:31 PM SendFile=C:\Documents and Settings\Admin\Desktop\Backup.sre, Mode=2
I E190 9:04:31 PM TalkToFlashloader (using COM4)
I E191 9:04:31 PM Switching over to flash loader
I E192 9:04:32 PM COM4 is connected to UART0
I E193 9:04:32 PM Sync'ing to flash loader
I E194 9:04:32 PM Querying device information
I E195 9:04:32 PM Flash loader version: V4.13
I E196 9:04:32 PM Max. TX/RX size: 65536/32768
I E197 9:04:32 PM Mobile transfer speeds: 57600, 115200, 230400, 460800
I E198 9:04:32 PM Detected flash chips: 2
I E199 9:04:32 PM 1: Manufacturer: 0x89, Device: 0x8857
I E200 9:04:32 PM 2: Manufacturer: 0x89, Device: 0x8856
I E201 9:04:32 PM 0x89/0x8857: Intel 28F128xW30, 128 Mbit (16 MB (16777216 Bytes) in 263 sectors)
I E202 9:04:32 PM 0x89/0x8856: Intel 28F128xW30, 128 Mbit (16 MB (16777216 Bytes) in 263 sectors)
I E203 9:04:32 PM Total flash size: 32 MB (33554432 Bytes) in 526 sectors
I E204 9:04:32 PM Port info:
I E205 9:04:32 PM Logical port 0: COM4 <-> UART0 at 115200 baud (~100%)
I E206 9:04:32 PM TalkToFlashloader: OK
I E207 9:04:32 PM Read region 0: 0x00000000 - 0x00001fff: 8 KB (8192 Bytes)
I E208 9:04:32 PM Read region 1: 0x00004000 - 0x00ffffff: 15 MB (16760832 Bytes)
I E209 9:04:32 PM Read region 2: 0x01000000 - 0x01ffffff: 16 MB (16777216 Bytes)
I E210 9:04:32 PM Data to be read: 31 MB (33546240 Bytes)
I E211 9:04:32 PM Setup
I E212 9:04:32 PM ReadData: 0x00000000 - 0x00000fff
I E213 9:04:32 PM ReadData: 0x00001000 - 0x00001fff
I E214 9:04:32 PM ReadData: 0x00004000 - 0x00004fff
I E215 9:04:33 PM ReadData: 0x00005000 - 0x00005fff
I E216 9:04:33 PM ReadData: 0x00006000 - 0x00006fff
I E217 9:04:44 PM FLSendCmd(suck): 5 (ERR_PROTOCOL)
I E218 9:04:44 PM Retry 1: ReadData
I E219 9:04:49 PM WaitFor4CCs failed: ERR_TIMEOUT (6)
I E220 9:04:49 PM 0x216e7973 = syn!
I E221 9:04:54 PM WaitFor4CCs failed: ERR_TIMEOUT (6)
I E222 9:04:54 PM 0x216e7973 = syn!
I E223 9:04:59 PM WaitFor4CCs failed: ERR_TIMEOUT (6)
I E224 9:04:59 PM 0x216e7973 = syn!
I E225 9:05:04 PM WaitFor4CCs failed: ERR_TIMEOUT (6)
I E226 9:05:04 PM 0x216e7973 = syn!
I E227 9:05:09 PM WaitFor4CCs failed: ERR_TIMEOUT (6)
I E228 9:05:09 PM 0x216e7973 = syn!I E229 9:05:09 PM Failed to sync
I E230 9:05:09 PM SendFile: 5 (ERR_PROTOCOL)
I E231 9:05:09 PM ReLoad: 5 (ERR_PROTOCOL)
I E232 9:05:09 PM Error code: ERR_PROTOCOL
E E233 9:05:09 PM Sorry, an error has occured ! (ERR_PROTOCOL)
I E234 9:05:09 PM ThreadProtocol finished
I E235 9:05:09 PM ThreadProtocol: 5
I E236 9:05:09 PM ThreadGUI finished
I have no clue what to do to try and resolve this. Thank you in advance for your help.
|
 |
Advertisement
|
|
|
|
|
facetoface
Posts: 8 |
Tue Mar 15, 2005 1:37 am |
|
I believe it's because you can't really turn off the phone since it keeps charging. I don't know how to turn that off or even if there is a way to. Does anybody know?
|
|
shmuil195
Posts: 3 |
Tue Mar 15, 2005 3:52 am |
|
I think your right because the screen turns on when I plug it in, even if the phone is "off".
|
|
i814u2
Posts: 2
Phone Model:
e715
Service Provider:
t-mobile |
Thu Mar 31, 2005 11:00 pm |
|
optiflash 4.12 worked fine for me, did you try that or just 3.6x and 3.7x? (or something else even...)
|
|
apape10
Posts: 23
Phone Model:
Samsung e770 & e720 & e715
Service Provider:
T-Mobile |
Sun Apr 03, 2005 4:26 am |
|
i set up the back up file and when opti flash is ready and says power on mobile! i plug in the cable in with the phone off and it works great...
|
|
shmuil195
Posts: 3 |
Sun Apr 03, 2005 4:35 pm |
|
Thanks apape10, I just tried it the way you did and it worked.
|
|
apape10
Posts: 23
Phone Model:
Samsung e770 & e720 & e715
Service Provider:
T-Mobile |
Mon Apr 04, 2005 12:15 am |
 glad to be of service...
|
