Used an OP Code, now phone is not detected via USB anymore..
Page 1 of 1
Author
Message
Spazmogen Posts: 6
Phone Model: v220
Service Provider: Rogers
Thu Jul 14, 2005 7:07 am
Hello.
My v220 is a tri-band model. I used the OP code to access the 850mhz band. The phone said success afterwards, so I guess it worked.
Now when I plug the phone in it's only detected by 1 program: Motokit 1.06
nothing else sees the phone.
I've tried:
Mobile Phone Tools 3.25 (used to work fine)
Data Pilot (used to work fine)
P2K Tool (used to work fine)
PST (used to work fine)
Does this sound like a driver issue or a hardware issue.
I completly back the phone up prior to with Mortola Service Software & MotoKit 1.06
Should I do a Master Reset ?
Advertisement
Old_Fool Posts: 2214
Phone Model: If it's locked, ican unlock it. If you brick it, I can fix it
Service Provider: ATT
Thu Jul 14, 2005 8:12 am
Spazmogen wrote:
Hello.
My v220 is a tri-band model. I used the OP code to access the 850mhz band. The phone said success afterwards, so I guess it worked.
Now when I plug the phone in it's only detected by 1 program: Motokit 1.06
nothing else sees the phone.
I've tried:
Mobile Phone Tools 3.25 (used to work fine)
Data Pilot (used to work fine)
P2K Tool (used to work fine)
PST (used to work fine)
Does this sound like a driver issue or a hardware issue.
I completly back the phone up prior to with Mortola Service Software & MotoKit 1.06
Should I do a Master Reset ?
Try to power fone off and on while trying to connect
Spazmogen Posts: 6
Phone Model: v220
Service Provider: Rogers
Thu Jul 14, 2005 8:31 pm
powering the phone on & off during the software connection stage makes no difference.
Should I just do a master reset?
Is there anyway to manually undo an OPCODE entry?
I'm not sure is MSS will work or not. I'm getting the no HASP loaded error.
duceduc Posts: 2124
Phone Model: iPhone1G, 3G Unlocked
Service Provider: Softbank
Thu Jul 14, 2005 8:56 pm
Using upcode entry shouldn't effect the phone. I could be mistaken, however. Try the master reset.
Spazmogen Posts: 6
Phone Model: v220
Service Provider: Rogers
Thu Jul 14, 2005 9:21 pm
Ok.
Master Reset did the trick.
But I was surprised to see my Java games were still there, as was the Engineering menu. So were all of my custom .mp3 ring tones & pictures that I took.
V220 (R365_G_0B.D2.23R) is what I've got. It's tri band, not quad band.
I'm back to tri band as I now have horrible recption here in the basement again. It was 3 or 4 bars most times after the OPCODE to enable 850mhz.
duceduc Posts: 2124
Phone Model: iPhone1G, 3G Unlocked
Service Provider: Softbank
Thu Jul 14, 2005 9:23 pm
a master clear will delete custom ringers, pic, games, wap settings, etc.
Spazmogen Posts: 6
Phone Model: v220
Service Provider: Rogers
Thu Jul 14, 2005 9:38 pm
Now when I try and use a back up from MotoKit 1.06 it says phone/type mismatch. Even though its the same phone. All I did was an OPCODE to enable 850mhz...odd.
P2KTools_v0.7.1.9 won't connect to it either...
Spazmogen Posts: 6
Phone Model: v220
Service Provider: Rogers
Fri Jul 15, 2005 9:52 am
One last update:
I did a master clear, and uninstalled the Motorola USB modem in control panel.
I then rebooted & reinstalled the motorola USB modem.
All programs work normally again.
So I did the OPCODE again. All seems fine now.
Mullin Posts: 1
Phone Model: v551
Service Provider: Cingular
Fri Jul 15, 2005 10:49 am
Something similar is happening to me I have a v551 and I got a usb cable and everything but when I try to hook it up to my computer it just searcher for phone but never ends up finding it. I was using the smartmoto program too.
captanham Posts: 14
Phone Model: razor
Service Provider: cingular
Mon Jul 18, 2005 6:05 am
why does everyone use the op codes to add frequencys? i'm lost and a noobe, trying to figure all this out
View more 
