HOW-TO: Get P2k Programs Connected

Last edited by mikekay10 on Sat Jan 13, 2007 6:08 pm, edited 2 times in total

Step 1. Get the software

Go to Motodev and download Motorola USB Driver (you will need to register)

Also download your chosen p2k program e.g. p2kMan

It would also be a good idea to locate RSD Lite – you will have to use Google to find this as it is classed as warez and we cannot give
links.

Step 2. Install the driver program

Extract the file “Motorola_EU_Driver_Installation.msi” from the zip file you downloaded.

Double click on this file and the installation will start.

Click next and the EULA will appear

Click on "I Agree" (obviously having read the agreement first Angel), then next.

The program will now install

Click close to end the install procedure

During the installation process you may see the following screen 1 or
more times

Should this appear hit "Continue Anyway"

Step 3: Install the drivers

You will now have a new program group in your start>programs menu -"Motorola Driver Installer", with a shortcut called "Motorola Driver Installer.exe" within it.

Make sure the phone is disconnected at this time.

Run this program, and it will check whether the drivers are already
installed, when this is complete you will see the following screen

Under "Operation Mode" (lower left), select "Clean and Reinstall" (the bottom option).

Then hit "Start"

The program will then do its thing. When it is finished hit "Exit"

You may get the message about Windows Logo testing again - if you do hit "Continue Anyway"

Step 4: Connect the phone

Make sure the phone is turned on then connect the USB cable. It is best
to use a USB port on the rear of the PC rather than front mounted ports
as these sometimes connect to the motherboard via a hub

When you plug the phone in Windows will find new hardware - Motorola
Phone (V3), then Motorola USB Modem. The installation should
complete without intervention.

You should now be able to connect using Mobile Phone Tools, the phone
should also be charging.

We now want to install the P2k Drivers. First make sure MPT is not
running.

Now with the phone still connected run one of the P2k programs, I generally use P2kMan - but thats just me. Its best not to use p2k Tools as this may start in AT mode and confuse matters.

When you do this Windows should find several new devices and after a
short while the new hardware wizard will run. In the rare event the new
hardware wizard does not start, install and run RSD Lite.

The first screen to appear asks if you wish to connect to Windows Update

Select "No, not this time", then click on "Next"

Choose "Install the software automatically (Recommended)", then hit "Next"

The driver for Accessories Interface is then installed, after a short
while the following screen is displayed

Click "Finish"

The new hardware wizard will then run again

Once again select "No, not this time", then click on "Next"

This time the wizard asks for drivers for "Data Logging MCU Interface".

Choose "Install the software automatically (Recommended)", then hit
"Next"

Again the drivers are installed then after a short while the
following screen is displayed.

Click "Finish"

The new hardware wizard will then run for a third time

At the first screen select "No, not this time", then click on "Next" in the same way as before

This time the wizard asks for drivers for "Test Command Interface".

Choose "Install the software automatically (Recommended)", then hit "Next"

Again the drivers are installed then after a short while the following screen
is displayed.

Click "Finish"

Your P2k drivers are now installed and the P2k programs should
recognise the phone

Remember if you connect using a different USB port in the future,
Windows will recognise new hardware and you will need to repeat these
steps

Step 5: Flash Interface Device

If at anytime you choose to flash your phone you will need the Flash
Interface device installed. This device is used to communicate with the
phone while it is in bootloader mode.

In order to run the hardware installation wizard for this device you
can do one of two things. Either use RSD Lite to flash the phone as
normal (browse to the file and hit start) and RSD Lite will switch the
phone to bootloader mode for you. Alternatively you can start in
bootloader manually (hold * and # while turning the phone on), then
connect the USB cable.

Either way the new hardware wizard will run again.

As before select "No, not this time", then click on "Next"

Choose "Install the software automatically (Recommended)", then hit
"Next"

Again the drivers are installed then after a short while the following screen
is displayed.

Click "Finish" and you are done - you can now flash your phone with RSD
Lite.

Once more remember if you connect using a different USB port in the
future, Windows will recognise new hardware and you will need to repeat these steps

I downloaded this with no problem, trying to increase volume on Razor V3 With Verizon service as carrier, using windows XP, I am using Bezols P2KTools, I can get it to connect to the phone, green Dot comes on the bottom saying phone is connected, But when I pull up the Gain table it has the Get Highlighted at the bottom, but the set is blacked out, I set the settings then hit Get, and the hour glass just comes on and stays, never changes, the computer just freezes up, not sure what I am doing wrong.

Thanks for any help

Rick

I'm not sure that will work with the V3c - I know very little about the CDMA models I'm afraid

hi. i use moto slvr l7. when i connect my phone and open p2k commander, the phone gets disconnected form my computer . what should i do .what is the to send themes to my phone. please help.reply to gowri_vsp@yahoo.co.in

hi. i use moto slvr l7. when i connect my phone and open p2k commander, the phone gets disconnected form my computer . what should i do .what is the to send themes to my phone. please help.reply to gowri_vsp@yahoo.co.in

that happened to me.You need to make your phone asks you to install bluetooth usb device.Here is how i did that or just i was lucky
first i went to p2k and it dissconnects my phone.I got frustated and i went to control panel,phone and modem options and i removed usb modem motorola but I DIDNT quit THE p2k PROGRAM.THEN i unplugged phone and plugged it again.It promted me to install 4 drivers i just pointed at drv directory in p2k program and everything else went good.I can send games to my phone just everything.But dont forget to enable java app loader you can do it after you install this drivers.

Was it effective?

any help for my problem a few posts up

Thanks

Last edited by Nokia on Thu Oct 12, 2006 3:10 pm, edited 1 time in total

rlfields have you installed all drivers correctly?You need to install 3 or 4 drivers i think.I will try to write them
Motorola usb modem
Bluetooth usb device
Motorola accesories
Motorola p2k acessories
I think are these one b ut not sure about last one.So did you installed them when you first went in p2k tools?
Hint:I found correctly drivers here in new p2k tools
http://rapidshare.de/files/22660071/newp2k.rar.html

GO TO NEXT PAGE I POSTED 2 POSTS

Yes it showed all the drivers as being installed, and when I pull up the p2k program and plug my phone in, it connects right up, red dot changes to green and says I am connected, but when I go to tools and bring down the volume it brings up the table gain, but if I try to change it just pulls up the hour glass and just sits there and freezes up.

HOW-TO: Get P2k Programs Connected

Similar Topics

New Motorola Cell Phones

Subscribe to Our Feed

Carriers Talk

Manufacturers Talk

Mobiledia Community