| Author |
Message |
rgnewton
Posts: 3 |
 
Sun Nov 19, 2006 3:18 pm |
Hello:
I flashed my Razr V3 today, and the phone is now dead. When I press the power button, the backlight displays briefly and goes out. the screen is blank. Also, my PC does not detect the phone; a message comes up saying "USB device not recognised".
Can anyone assist me? Does this mean that I have to dump the phone?
|
 |
Advertisement
|
|
|
|
|
mikekay10
Posts: 2958
Service Provider:
Vodafone |
Sun Nov 19, 2006 3:58 pm |
What file did you flash?
Were there any errors in the process or did the phone go flat or any other problems?
Can you start in bootloader (hold * and # while powering on)
|
|
rgnewton
Posts: 3 |
Sun Nov 19, 2006 4:58 pm |
Hello:
The phone went flat after flashing. I'll try * and # simultaneously while depressing the power button.
|
|
rgnewton
Posts: 3 |
Sun Nov 19, 2006 5:10 pm |
Hello again Mikekay10:
I got the phone to detect after pressing * and #. I'm retrying the installaion of the Monster Pack. The phone screen indicates that the "SW Upgrade is in progress".
Will keep you informed...
|
|
rodrigjo027
Posts: 3 |
Mon Nov 20, 2006 11:37 pm |
|
Same problem ,let me know how does it go.... I reflashed with AP_CINGULAR_MODDED_MP.shx and still the same problem
|
|
mikekay10
Posts: 2958
Service Provider:
Vodafone |
Tue Nov 21, 2006 4:07 am |
|
If the phone goes flat mid flash this can often corrupt the PDS - in which case if you do not have a backup you will need a Smartclip to rebuild it
|
|
rodrigjo027
Posts: 3 |
Wed Nov 22, 2006 9:01 pm |
Do u know if the Smart Clip work with the phone when it does not even go to the flash mode with * and # and power.
Thanks
Jorge
|
|
mikekay10
Posts: 2958
Service Provider:
Vodafone |
Thu Nov 23, 2006 3:25 pm |
|
Old Fool is the expert on this - look for a post by him and send him an email
|
|
Old_Fool
Posts: 2196
Phone Model:
If it's locked, ican unlock it. If you brick it, I can fix it
Service Provider:
ATT |
Sat Nov 25, 2006 11:52 am |
|
Yes it will fix it, the worst case is to test point then Smart clip will see it then repair it form there
|
|
brad9m
Posts: 3
Phone Model:
V3m
Service Provider:
Verizon |
Sat Nov 25, 2006 10:32 pm |
I have the same problem with my V3. I flashed the Cingular monster pack (R374_G_0E.40.57R_PDS001_LP0003_DRM0001_JPJAVA_G_0E_V3_06_03R_GSMV3xxC IN01NA065_1FF) from motox and it crapped out both phones I tried it on. For one of them I was smart enough to make a back up using FlashBackup 2.62 and reflashed using (R374_G_0E.42.09R_MXLP0001_GSMV3MXCIN01NA0F5_superfile_MOTOX). For the other one I wasn't as smart. I've tried almost everything, except what old fool mentioned above. Here's the background:
I used scotty's BL downgrader and flashed my phone with a cingular unbranded monsterpack. After flashing it just entered the bl screen. I didn't backup the phone before I started modding (duh). I tried the tut http://www.motox.info/showthread.php?t=11727 but I can't get past flashing the rfdi image. I also tried using the PDS retore function on Repair Studio and creating a new PDS using Flash Backup 2.62. So, I decided to pick up a Motorola Smart Clip off ebay. I tried to restore the PDS file using SmartMoto and it fails saying that the phone may be locked (which it isn't). I have exhausted all of the ideas that I have. Can anyone else offer some suggestions, or do I give my mother in law a pink V3 paperweight???
SmartMoto error:
Searching for phone... found S Flash Neptune LTE, getting test interface... interface not found
Switching to flash mode... OK
Reading phone boot version... 8.23
Sending boot... load error
Warning: Phone may need "Remove RSA" procedure to get unlocked or flashed, check model list at "Unlock" tab if flash mode fails to start
Now I guess I'll try the testpoint thing...
|
| | |
|
|
|
 |
 |
 |
Sign up for a roundup of the day's top stories. |
|
|
View more 