| Author |
Message |
younger
Posts: 7 |
 
Wed Dec 27, 2006 1:57 am |
Hi,
I read carefully the instructions about unlocking V3. I tried many times but failed, terrible.
The boot loader is 08.26. I downgraded it to 07.D0, then no DOS screen as the software mentioned.
After flashing other version such as 42.10 it can start but no service.
I then tried to flashed R374_G_0E.40.79R it can not normally start, only in DOS but still no screen (I can see it in hardware list in my PC). Then I used unlock, it seemed ok but it still cannot start.
I have to flashed it to 42.10 same as before, no service signal.
The biggest problem is when flashing R374_G_0E.40.79R the cell phone can not start.
Can anybody help this?
Many thanks!
Younger
|
 |
Advertisement
|
|
|
|
|
younger
Posts: 7 |
Wed Dec 27, 2006 2:50 am |
I got p2k easy tool and used it. The following information showed it was ok. but when I put my original SIM card in there still no signal. so sad!!!
Connecting to phone ...
Switching to P2K mode ...
Connected to: 'Motorola Test Interface'
Switching to flash mode ...
Connected to: 'Motorola Flash'
Connected OK
Bootloader version: 07D0
Sending loader to phone ...
Loader sent OK.
Get info from phone ...
PDS info: PDS_4007
ADR info: 126E05A8
Powering down...
Connecting to phone ...
Switching to P2K mode ...
Connected to: 'Motorola Test Interface'
Connected OK
Unlocking ...
Unlock OK
Powering down...
|
|
younger
Posts: 7 |
Wed Dec 27, 2006 10:37 pm |
Till now it seems no "subsidy code" needed but it still has no signal.
I did not backup PDS but I have another V3 RAZR at hand. Can I use that backup to restore in this one? or just use p2k easy tool to repair PDS?
Many thanks for any suggestions!!!
Younger
|
|
Old_Fool
Posts: 2118
Phone Model:
If it's locked, ican unlock it. If you brick it, I can fix it
Service Provider:
Tmobile |
Thu Dec 28, 2006 11:58 am |
YOu can not use back up form one fone to another.
PDS is IEMI specific
|
|
younger
Posts: 7 |
Thu Dec 28, 2006 1:57 pm |
old_fool: could you please tell me how can I do to save my V3?
a ton of thanks!
|
|
wine_guy
Posts: 3
Phone Model:
v3
Service Provider:
Cingular |
Thu Dec 28, 2006 2:08 pm |
Just because you can't see the boot screen doesn't bean it's not there. It is very common for the bootloader screen to show up VERY dimly, sometimes you can't see it at all after downgrading the bootloader.
I don't think you'll be able to use p2k easy tools to reapair the PDS, you will need a smart-clip for that.
|
|
younger
Posts: 7 |
Thu Dec 28, 2006 2:38 pm |
|
wine_guy: you mean I have to send it to someone who has a smart-clip to fix PDS?
|
|
younger
Posts: 7 |
Thu Dec 28, 2006 2:54 pm |
HHoooooooooooo
I made it!!!!!!
I just change the network setup to automatic, then I got the signal!!!! And I can call out!!! WWWooowww.......
|
|
Malibu21
Posts: 1002
Phone Model:
V3xx Lightly Modded, V6 Maxx Tweaked nicely.
Service Provider:
The New AT&T |
Thu Dec 28, 2006 3:53 pm |
|
Good to see you fixed it
|
